- Welcome to the New Customer Disruption Newsletter
- Kroger debuts Retail Site Intelligence, new enterprise IT architecture
- Westfield Garden State Plaza brings digital technology to physical world
- Animated mannequins steal show at Gaultier exhibit in New York
- Walmart to install LEDs in ceilings, cutting lighting energy use by 40%
The big-box construction track at SPECS/2007 covered such topical issues as the impact of today’s global economy on the construction industry and suggestions on how best to deal with increasingly restrictive sign ordinances. In the “Don’t SWPPP This Away!” workshop, the risks and costs of non-compliance were discussed. The session included permitting case studies of non-compliance and strategies for dealing with regulators.
The sessions included ample opportunities for audience interaction. In the “Comparison of Construction Contracting” workshop, attendees were given an overview of the various types of construction contracting methods and provided with an analysis of risk/reward for each type. They participated in roundtable discussions to analyze specific scenarios.
In the session, “Pardon the Interruption” workshop, a retailer and a contractor debated nine hot-button topics, including bidding, regular bidding vs. reverse auctions, and change orders.
Cement: The “CSI: Concrete” workshop provided an in-depth look at concrete-and moisture-related issues. Industry expert Howard Kanare, senior principal scientist, CTL Group, Skokie, Ill., presented common problems and proven techniques for preventing and/or fixing concrete moisture complaints.
The workshop examined the different modes that concrete-floor moisture failures may take, from curling, flooring expansion and staining to condensation, debonding and adhesive breakdown. The speaker outlined several key concepts for attendees to keep in mind, starting with the idea that the floor is part of the building envelope. Leaks are not acceptable.
“Design and build to avoid moisture-vapor intrusion from below and around the floor,” Kanare said.
Attendees were also urged to remember that the floor is a system and, as such, compatibility of components is key.
“Design for resistance to moisture vapors,” Kanare said, “and always consider contingencies, such as warping, flatness and moisture.”
Kanare also discussed vapor retarders. He made the point that every floor slab-on-ground should have a vapor retarder directly under the slab, properly detailed, and protected from damage during construction of the floor.
Drying is critical to avoiding moisture problems at a later date. Kanare recommended the use of a concrete mix that will dry quicker (look for such features as moderate water-cement ratio, 0.45 to 0.50; low-absorption aggregate; maximize coarse aggregate size and volume; moderate cementitious factor and water-reducing admixtures). He said the drying process should be measured and monitored and that active drying means should be provided.
“Avoid air stagnation, which slows drying,” Kanare explained. “Circulate the air. “And be aware of daily weather cycles.”
It is important to measure moisture, Kanare said, for a number of reasons. These include meeting the flooring manufacturer’s requirements, minimizing potential indoor air-quality problems, minimizing moisture-induced failures, meeting warranty requirements and minimizing liability.
The session also examined the various approaches to remediation. Understanding the root cause of the problem is essential, according to Kanare, who added some recommendations.
How would you describe SPECS?
“If it’s external moisture, cut off the supply. If there is no external moisture source, dry the floor,” he said.
Signage: In “Size Matters: Signs of the Times,” Peter Hauser, president, Site Enhancement Services, South Bend, Ind., shared strategies for maximizing exterior-signage visibility and ways to deal with restrictive sign ordinances. The speaker noted that municipalities restrict signage based on aesthetics as well as safety.
Typically, signing is regulated by the zoning ordinance contained in the city plan.
“New signs must meet the sign standards [of the municipality] or go through a variance process,” Hauser said. “If the applicant is denied, he can often appeal to the city council.”
However, some municipalities create design review boards that review all signage regardless of size or design. These boards can enforce requirements on the business owner whether or not the sign is code-compliant, according to Hauser.
The speaker emphasized the importance of developing an effective permit strategy.
“Permit the signs early,” he said. “Design your sign standards to maximize code allotments.”
The speaker urged the audience to research the city code before choosing a site to determine if the code is restrictive or lenient.
“Survey the area to see if a variance is possible,” he added. “For instance, do other businesses have non-conforming signs?”
To deal with restrictive sign codes, Hauser recommended creating a flexible sign program, with signs that can be built at different heights and in different sizes.
“Choose a sign that is a reasonable variable,” he said, “and have an option two if your variance fails. For instance, a smaller sign that still provides adequate identification, or a secondary logo in case the primary one causes problems.”